We have encountered this post involving Tools You Need to Install a New Bathtub down the page on the net and thought it made perfect sense to relate it with you over here.
Mounting a bath tub isn't precisely rocket science, but it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably hard task. If the old tub is conveniently obtainable, the project can move quickly; if you need to open up a wall to remove the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will certainly require a helper to move out the old tub as well as set in the new one. Ensure you have actually qualified yourself for the job and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed task, it is better to take into consideration using one prior to you start. Opportunities are you might need a specialist plumber to make tube links.
This post will certainly help you install a new bath tub in your restroom if you have already purchased a brand-new tub as well as don't need to change the arrangement of your previous water system pipelines.
Your tools as well as material checklist need to make up the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bath should be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps system to avoid strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final position.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the restricted access that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bathtub in the required position. The wood boards are useful in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the bathtub till the spirit level checks out degree.
To mount faucets, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water and check all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as likewise check the overflow electrical outlet and also the normal outlet for leaks.
Lastly, fix the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the tub must wait till the bath tub has been utilized at least once as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines are in area between the tap and the sink. Secure the faucet in place with the supplier offered backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bathtub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can split relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very taken with Tools You Need to Install a New Bathtub and I'm hoping you appreciated the new blog entry. Sharing is caring. Helping people is fun. Thank you so much for taking the time to read it.
Facing a flood? Call us!